E-Waste Shredding and Sorting Line

11/18/2026
Author:Recycle-Machine

Small Domestic Appliances (SDA)—ranging from microwave ovens, vacuum cleaners, coffee makers, and electric fans to power tools and desktop printers—represent the fastest-growing volume in municipal WEEE (Waste Electrical and Electronic Equipment) streams. Unlike large refrigerators or CRT monitors, small appliances contain complex mixtures of ferrous steel shells, copper motor windings, cast aluminum brackets, brass connectors, and high-grade engineering plastics (ABS, PP, PS, PC) locked together by hundreds of screws and snap-fits.

Manual dismantling of small household appliances is slow, labor-intensive, and economically unviable in regions with rising wages. Henan Resyke Machinery Equipment Co., Ltd. provides a fully automated e-waste shredding and sorting line that transforms mixed SDA scrap into clean, furnace-ready metal fractions and high-purity plastic regrind in a single continuous pass.

Step-by-Step Engineering of an Automated SDA Recycling Line

To maximize e-waste recycling plant profit, a processing line must liberate entangled components without pulverizing brittle plastics into unmarketable dust. Our turnkey system achieves this through four synchronized stages:

1. Primary Pre-Shredding (Double-Shaft Shear Shredder)
Whole small appliances, tangled power cords, and internal electric motors are fed via a heavy-duty chain conveyor into a low-speed, high-torque e-waste shredder. Equipped with thick alloy hook blades, it tears open plastic housings and motor stators into 40–80 mm chunks while resisting shock loads from hardened steel shafts.

2. Secondary Crushing & Component Liberation (Vertical / Hammer Mill)
Pre-shredded material enters a heavy-duty hammer crusher or vertical chain mill. High-speed impact breaks apart copper coils, aluminum die-cast parts, and plastic casings into uniform 15–30 mm fragments, achieving 99% separation between metals and polymers.

3. Ferrous Removal (Overband & Drum Magnetic Separators)
Before non-ferrous sorting, strong neodymium magnetic separators extract 100% of iron screws, transformer silicon-steel sheets, and steel casings. Removing ferromagnetic contaminants is critical to protecting downstream sorting belts and maximizing non-ferrous purity.

4. Non-Ferrous Recovery (High-Frequency Eddy Current Separator)
Buyers often ask how an eddy current separator extracts copper and aluminum that magnets cannot attract. Inside the head pulley of Henan Resyke’s eddy current separator, an eccentric high-speed rare-earth magnetic rotor spins at over 3,000 RPM. When non-ferrous metals (aluminum, copper, brass, zinc) pass through this alternating magnetic field, induced eddy currents generate a repulsive magnetic force that physically ejects the metals forward over a splitter plate, leaving non-metallic engineering plastics to drop cleanly off the belt.

Why Eccentric Rotor Design Boosts Your Profit Margins

Not all eddy current separators perform equally on shredded small appliances, which often contain fine 3–15 mm copper wire fragments and thin aluminum heat-sink fins:

Concentrated Magnetic Flux: Our eccentric magnetic rotor focuses maximum Gauss intensity precisely at the material discharge point rather than spreading it across the entire drum circumference.

Zero Ferrous Burnout Risk: Unlike concentric rotors where trapped iron nails can heat up through induction and burn through the conveyor shell, the eccentric geometry allows residual magnetic particles to drop away safely once they leave the focused magnetic sector.

98.5%+ Non-Ferrous Recovery: Cleanly separates valuable copper armatures, brass plugs, and cast aluminum from mixed ABS/PP plastics, increasing overall material resale value by 35% to 50% compared to selling unrefined shredded WEEE mixed scrap.

Get Your Custom E-Waste Shredding Plant Layout & ROI Sheet

Whether you are upgrading an existing scrap yard with a standalone e-waste shredder for sale or commissioning a 2 to 10 ton/hour complete WEEE sorting plant, Henan Resyke Machinery Equipment Co., Ltd. delivers custom engineering from factory floor design to on-site commissioning.

Start Your Project Consultation at machineryrecycle.com:

Share your daily WEEE tonnage, appliance mix, and target output size with our engineering specialists.

Get a free customized process flow diagram, equipment configuration list, and factory-direct quotation today.

Get Quotes

    Please enter a valid email address